What’s interesting is that many of these largest engine lumps weren’t intended for muscle cars – they were intended to go under the hoods of full-sized luxury cars
So which one of these was the biggest engine in the world to come from Detroit?
The 440 CID engine was produced from 1965 until 1978, making it the last version of the Chrysler RB big block
From 1967 to 1970, the high-performance version was rated at 375 hp with a single four-barrel carburetor, and from 1969 to 1971, but with three two-barrel carburetors (“440 Six Pack” for Dodge, “440 6 Barrel” for Plymouth) the motor produced 390 hp
For 1972 all engines, including the expensive new 440, featured lowered compression, more conservative cam timing, and other changes to comply with tighter emissions regulations
The 1972 440 produced only 335 hp gross, and 225 hp under the new SAE net rating system
Engine power dropped a bit each year until 1978, when it was rated at 255 hp (in police specification) and limited to large sedans and police packages
Number Five (tie): Pontiac 455, Oldsmobile 455, Buick 455
The first to enter service was the Pontiac, dating back to 1955 (same year as the small block Chevy)
The Pontiac engine maintained the same externally dimensions through its entire life (with the exception of deck height), the last Pontiac engines were produced in 1981
The only identifier used to differentiate the smaller displacement engines from the larger ones was by crankshaft journal size
The Pontiac 455 engine featured the larger 325″ journals
With a longer stroke than bore width, the naturally aspirated engine was geared more to the production of low-speed torque than top end horsepower
The 1970 HO version of the 455 produced 370 hp but with a diesel-like 500 lb-ft of torque
To final installations were in 1976 when emissions hardware and unleaded fuel requirements sucked power down to a net of 200 hp
The “big block” version, was brought out in 1965, which shared the same dimensions as the “small block”, except for an increased deck height to accommodate a longer stroke
The ultimate version of the engine was installed in the 1968 – 1970 full-sized front wheel drive Toronado GT coupe, in its W34 form, and produced 400 hp gross
Production continued through 1976, which produced 275 hp net in its final form
In 1967 Buick introduced a new “big block” design to replace the infamous “Nailhead” V8
In regards to bore:stroke ratio, it was the opposite of the Pontiac engine, an oversquare (large bore than stroke) design, which should be better suited to high revs and higher horsepower, usually the the expense of torque
Oddly though, it generated 10 ft-lbs more than the comparable Pontiac and was the highest torque output of any engine in the first muscle car era
Horsepower seems strangely out wack as well, with the high-performance GSX Stage 1 package rated at just 360 hp for 1970
Designed as a replacement for the older MEL 462 V8, the 460 version of the Ford “385” family of motors was designed for smooth, quiet driving (unlike its “385” brother the Ford 429) as installed in the Lincoln Continental
The engine produced 365 hp (gross), limited by its relatively small carburetor
The 460 was phased out for use in passenger cars in the late 70s, but continued to be produced with minimal modifications in trucks, RVs, and boats until production ceased in 1997
Despite near identical engine displacements, the Lincoln 460 and Lincoln 462 are completely different engines
The Lincoln 462 was based on the MEL engine block architecture (Mercury-Edsel-Lincoln), first produced in 1958
The 462 engine produced 340 hp and was used only in Lincoln Continentals, from 1966 until mid-year in 1968 when it was replaced by the 385-series 460
If you’ve been wondering where on our list the Big Block Chevy has been hiding, here it is
Where Ford and Dodge turned to V10 designs to create gasoline-powered engines for their larger pickups, GM dusted off the 454 big block and almost completely redesigned it for Chevy and GMC trucks, vans, and Suburbans
Chevy retained the same bore diameter as the old 454 , but the stroke was upped by 037 in to reach 496 CID (81L)
Power output was 340 hp, which compares favorably to the 1972 LS5 454 output of 270 hp (both SAE net, with the Vortec meeting even stricter emissions regulations than the LS5)
Cadillac had its V8, but its design limited its displacement to 429 CID, less than Lincoln and Chrysler
As a result Cadillac developed an all-new engine for 1968, a 375 hp V8 with a displacement of 472 CID
In 1970 Cadillac raised the displacement again by stroking the motor to 500 CID
It was rated at 400 hp with a truck-sized 550 lb·ft of torque
As emissions and mileage regulations came into effect, each passing year took a toll on the engine’s output For 1971 compression was reduced from 10:1 to 85:1, which dropped power to 365 hp, or 235 horsepower under the new SAE net ratings
There was a brief reprieve with the introduction of an option fuel injection system where power rose back up to 215 hp net, however the big motor’s days were numbered and it was dropped after the 1975 model year
Note: Ford did produce a Super Duty V8 (not to be confused with the Ford Super Duty model of truck) from 1958 to 1981 for medium- to heavy-duty trucks in three displacements: 401, 477
These were heavy, slow-revving motors designed for buses, concrete mixers, and garbage truck applications
There’s no evidence these engines were installed in any passenger vehicles at the Ford factory
5 Detroit Engines That Weren’t For Public Consumption!
You’ve seen the biggest, but how about something more obscure like these 5 mystery muscle motors of the 1960s that Detroit never sold in a car?
Overhead camshaft engines are commonplace today, but Detroit has been tinkering with OHC V8s since the ’60s
While some of the most iconic engines of all time were those that made their way into production cars of the ’60s, it’s highly likely that you’ve never heard of any of these high-horsepower beasts
From experimental designs to beefed-up takes on existing motors, this group will surely make you wish some of these engines actually evolved into a real production engine, as each is more impressive than the last!
Ford built three experimental 289s with a unique single overhead camshaft design that features a cam located in each of the cast aluminum valve covers (instead of on top of the cylinder heads)
In the original camshaft position within the engine is smooth shaft whose role is to drive the distributor as well as the two overhead cams
The purpose of this project was to raise the maximum engine speed and with it peak power
The OHC 289 produced 300 HP at 6500 rpm
But as the stock HiPo 289 already made 271 hp, and Shelby was getting 306 hp with bolt-on parts, it was deemed that this internal combustion engine was not worth pursuing
As part of the development of the Oldsmobile 455, Olds engineers wanted to take the design of the engine as far as possible
The ultimate version added a set of dual overhead camshaft cylinder heads to the mighty engine
A gear drive supported by roller bearings in an aluminum gear case at the front of the motor spun the cams, while a driveshaft was used in the standard camshaft position to transmit motion to the oil pump and distributor
Toward the end of 1969 engineers dyno tested the DOHC W43, built with a very racy122:1 compression ratio, and recorded a very flat (and fat) torque curve
Peak power Olds engineers recorded was 700 horsepower at close to 7000 rpm
Cole announced that all GM divisions would lower the compression of their motors so 91 octane unleaded fuel could be used, and development stopped on the DOHC Olds
Most likely prompted by its development of the Pontiac OHC six, the GM division built three different experimental SOHC 421 CID V8 engines in the early 1960s
According to the engineers who worked on the project, the SOHC 421 engines produced around 625 hp and were capable of turning 7,000 rpm
One version of the engine featured camshafts driven off the front of the engine, another design had the cams driven by gears off the back of the engine
As part of the General Motors V-Future cars program, Cadillac developed an overhead cam V12 slated for production in the late 1960s
Six prototypes engines were built in 1963 and 1964, all with a 60-degree architecture, chain driven overhead camshafts and hydraulic finger followers
A number of different induction systems were tested, including a single four-barrel, dual four-barrel, and triple two-barrel carburetors, as well as mechanical fuel injection
Based on the power output listed above you can see why the Cadillac V12 program was killed
Another tragic tale of concept cars and engines not living up to the hype
It’s unknown whether this project was purely for racing, or Plymouth had the intent to offer the motor in a street car at some point
Keep in mind that the entire Chrysler group witnessed the excitement and positive impact on the brand when the previously race-only 426 Hemi was offered in production cars
Following the 1968 season, Richard Petty announced he was leaving Chrysler and going to Ford for the 1969 NASCAR season
The money allocated for Petty was used to develop the Plymouth Indy DOHC V8
Design work began in February 1969 and running engines were provide to Andy Granatelli’s STP race team less than 90 days later
The designer of the special cylinder heads was Harry Weslake, a British engineer best known for his expertise in gas flow through internal combustion engines
If you recognize the name, it may either be for his V12 engine in Dan Gurney’s 1967 Belgian GP winning Eagle, or the Gurney-Weslake cylinder heads used on GT40 Fords
The engine lacked top-end horsepower necessary to compete and produce a potent enough top speed at the high speed oval tracks, it had plenty of bottom-end torque which made it quite competitive on the short oval
In fact, Art Pollard drove the Plymouth-Westlake engine to victory at the 200-mile Indy car race at Dover, Delaware on August 24, 1969
This would turn out to be the only victory for Plymouth in the history of Indy Car racing
Bonus: 5 Of The Best 60s Muscle Car Motors!
So you’ve seen the biggest and some of the more obscure engine models out there, but which power plants were actually the greatest muscle car engines of the Swinging Sixties?
In only the last few year have engineers been able to leapfrog the performance of engines built 50 years ago, engines that have long since become legend, their presence in a restored muscle car not only bringing extra dollars on the auction block but plenty of oohs and aahs from onlookers poking their heads under the hood at auto shows and in car reviews
In reality, when freshly rebuilt versions using 100% stock components have been run on a dynamometer, their output is consistent with what the factory stated
Recall that the engineers of the 1960s could predict airflow through CFD (computational fluid dynamics), deliver fuel via a direct injection system that pulsed the output to assure the best possible mixture, computers that consistently monitored all engine functions that allowed maximum performance under the available condition, or any of the other tools and gizmos available to engines today
The most these pioneers of performance had at their disposal was a flow bench, a dyno, but mostly their own experience and skill, yet they still created some of the most memorable motors in the brief history of the automobile
The famous side-oiler configuration of the FE (Ford-Edsel) block was developed for the Shelby Cobras as they moved up a class in international sports car racing
The engine was quickly adopted as the block of choice among all competitors because of the path of oil through the engine allowed it to rev above
Very few 427s made it into production cars and most of the those were intended for racing, particularly stock-based drag racing classes
Rated at 425 hp in Gross trim, output was consistent with its competitors
Ford even experimented with a SOHC version of the engine, but it was never installed in a production car
While the 427 designed as a race engine (and a very successful one winning the 24 Hours of Le Mans 24 fitted to the GT40 and the Daytona 500 with a Fairlane) it was a little too finicky to be a street motor, so the 428 was created to meet that need
Chrysler had been playing cat and mouse with NASCAR for a number of years regarding the legality of the Hemi engine, which had as of yet not actually been delivered to a paying customer in a passenger car
By 1966 Chrysler had no choice and offered the Hemi in a number of different models, and not just performance cars
There were several plain-jane Coronet four-door sedans ordered with the “eleplant motor” Displacing 70 L (426 CID), the engines were both massive and expensive to build, so only 11,000 were installed in passenger cars between 1966 – 1971
The engine produced 425 hp in “gross” form and 350 hp in “net” trim
To bypass corporate rules that limited engine sizes, racers used the special-order (COPO) system to get the cars they wanted
When ordering COPO 9560 you received a Camaro with an all-aluminum 427 CID ZL-1 big block
Unfortunately for us, just 69 ZL-1 Chevrolet Camaros were produced, but not surprisingly as each engine was hand-built and cost over $4,00, more than the cost of a base V-8 coupe
Though rated at 430 hp gross, the ZL-1 made 376 hp in its net configuration, not inconsistent with the output Chrysler was pulling from the Hemi
Perhaps the best muscle car street engine of the era was the Ford Boss 429
Completely unrelated to either the 427 and 428, both which were based on the Ford FE block, the 429 was developed around the new 385 block (the name comes from its original crank stroke, not its displacement)
It used four bolt mains, a forged steel crank and rods, and aluminum cylinder heads, which had a modified Hemi type combustion chamber topped by a used a single Holley four barrel carburetor mounted on an aluminum intake manifold
The Ford Boss 302 was built for one purpose – to win the Trans-Am Championship against Camaro, Challenger, Barracuda, and Javelin
The small block V8 motor was created by mating the heads from the yet-to-be-introduced Ford Cleveland V8 to the a 4 bolt heavy duty block of the Ford Windsor
The heads are “tunnel-port” where the pushrod runs a straight path through brass tunnel in the intake runner allowing for better airflow, a design adopted from the 427 FE
In stock form it produced 290 HP in “net” trim, only 60 hp less than the Hemi that 30% larger
Here are the 7 largest V8 engines by family that Ford ever built
We selected the largest displacement version from each of Ford’s large V8 engine families
If you scan down the list and don’t see your favorite motor, it’s likely not the largest capacity of that engine’s architecture
But we’ve tried to mention any popular ford engines within the listings that an enthusiast might feel had been overlooked
Designed primarily as a light truck engine, the 379 Boss (internal naming only) is a 379 CID (62 L) V8 that features a 2-valve per cylinder SOHC valve train with dual-equal variable cam timing, roller-rocker shafts and two spark plugs per cylinder
The engine develops 411 hp and 434 lb-ft of torque
The 62 L V8 has lightweight aluminum cylinder heads and pistons but utilizes a cast iron cylinder block for extra durability as its designed primarily for light truck applications, including the 2013 Ford Raptor
In need of a large engine to replace the aging, and heavy big block “385” (429/460) engines, Ford increased the capacity of the 351 engine to 400 CID
Billed as the 351 Cleveland’s big brother, the 400 was designed to provide brisk acceleration for big, heavy, full-sized cars
The deck height was raised significantly to accommodate the increased displacement, but the long rod length was excellent for producing that Ford and its customers sought
The 400 was only ever a passenger car engine with no sporting aspirations – it was available only with a two-barrel carburetor and a cast-iron exhaust manifold
A member of the famous FE (Ford Edsel) family that included the famous 427 side oiler and the 427 SOHC “Cammer” engines, the 428 is the largest of all FE motors by one cubic inch
It came into being as the 427 block was expensive to manufacture as the cylinder walls were so thin
As a solution, Ford utilized a narrower 4135″ bore with a longer 3985″ stroke, creating an easier-to-manufacture engine with nearly identical displacement
Performance versions of the 428 engine included the Cobra Jet and the Super Cobra Jet
The largest of the MEL (Mercury Edsel Lincoln) big blocks, the 462 was brought online in 1966 exclusively for Lincoln Continentals
The 462 MEL engine produced 340 hp and as much as 485 lb-ft of torque
Not intended for hot rodding, the engine was developed to provide a smooth delivery of power
That fact that it was fitted with a Carter AFB four-barrel carburetor says more about the amount of air and furl the engine needed to draw than any performance aspirations
The Ford 385 engine family (the name coming from the 385 inch crankshaft stroke of the 460 V8 was the Ford Motor Company’s final big block V8 engine design, replacing the Ford MEL engine and gradually superseding the Ford FE engine family
The engines were in production between 1968 and 1997
Some of the more famous versions of the 385 include the Cobra Jet, Super Cobra Jet, and of course, the Boss 429
However, Ford created a crate motor from the 383 block that displaced 514 CID and developed 625 hp straight out of the box
2 534 CID Super Duty V8
Ford’s Super Duty V8 was introduced in 1958 as a replacement for the Lincoln Y-block (with a maximum displacement of only 332 CID in truck applications)
The Super Duty was available in displacements of 401, 477 and 534 cubic inches
The Super Duty engines were large, heavy, high torque engines which operated at a relatively low RPM
The 534 produced 363 hp and 490 lb-ft of torque
Never intended for use in an automobile they were most commonly found in medium and heavy duty trucks of the time
Originally designed as a V12 for aircraft applications, the Ford GAA V8 was created by loping off two cylinders on each bank (and still utilizing the same 60 degree V angle)
Intended to power M4 Sherman tanks during WWII, the Ford GAA is very sophisticated for its time
It’s an all-aluminum 32-valve DOHC V8 engine, with dual Stromberg NA-Y5-G carburetors, dual magnetos and twin spark plugs making for a redundant ignition system
The GAA displaces 1,100 CID (18 L) and produces well over 1,000 ft-lb of torque from idle to 2600 rpm
The factory-rated output was 525 hp @ 2800 rpm